PVAG Chapter 9

CHAPTER 9: BUILT-IN ELEMENTS

V901 General

V901.1 Scope.  The provisions of Chapter 9 shall apply where required by Chapter 2 or where referenced by a requirement in this document.

V902 Dining Surfaces and Work Surfaces

V902.1 General.  Dining surfaces and work surfaces shall comply with V902.2 and V902.3.

EXCEPTION:  Dining surfaces and work surfaces for children’s use shall be permitted to comply with V902.4.

V902.2 Clear Deck Space.  A clear deck space complying with V305 positioned for a forward approach shall be provided.  Knee and toe clearance complying with V306 shall be provided.

V902.3 Height.  The tops of dining surfaces and work surfaces shall be 28 inches (710 mm) minimum and 34 inches (865 mm) maximum above the finish deck surface.

V902.4 Dining Surfaces and Work Surfaces for Children’s Use.  Accessible dining surfaces and work surfaces for children’s use shall comply with V902.4.

EXCEPTION:  Dining surfaces and work surfaces that are used primarily by children, 5 years and younger, shall not be required to comply with V902.4 where a clear deck space complying with V305 positioned for a parallel approach is provided.

V902.4.1 Clear Deck Space.  A clear deck space complying with V305 positioned for a forward approach shall be provided.  Knee and toe clearance complying with V306 shall be provided, except that knee clearance 24 inches (610 mm) minimum above the finish deck surface shall be permitted.

V902.4.2 Height.  The tops of tables and counters shall be 26 inches (660 mm) minimum and 30 inches (760 mm) maximum above the finish deck surface.

V903 Benches

V903.1 General.  Benches shall comply with V903.

V903.2 Clear Deck Space.  Clear deck space complying with V305 shall be provided and shall be positioned at the end of the bench seat and parallel to the short axis of the bench.

V903.3 Size.  Benches shall have seats that are 42 inches (1065 mm) long minimum and 20 inches (510 mm) deep minimum and 24 inches (610 mm).deep maximum.

V903.4 Back Support.  The bench shall provide for back support or shall be affixed to a wall.  Back support shall be 42 inches (1065 mm) long minimum and shall extend from a point 2 inches (51 mm) maximum above the seat surface to a point 18 inches (455 mm) minimum above the seat surface.  Back support shall be 2½ inches (64 mm) maximum from the rear edge of the seat measured horizontally.

V903.5 Height.  The top of the bench seat surface shall be 17 inches (430 mm) minimum and 19 inches (485 mm) maximum above the finish deck surface.

V903.6 Structural Strength.  Allowable stresses shall not be exceeded for materials used when a vertical or horizontal force of 250 pounds (1112 N) is applied at any point on the seat, fastener, mounting device, or supporting structure.

V903.7 Wet Locations.  Where installed in wet locations, the surface of the seat shall be slip resistant and shall not accumulate water.

V904 Sales and Service Counters

V904.1 General.  Check-out aisles and sales and service counters shall comply with the applicable requirements of V904.

V904.2 Approach.  All portions of counters required to comply with V904 shall be located adjacent to a walking surface complying with V403.

V904.3 Check-Out Aisles.  Check-out aisles shall comply with V904.3.

V904.3.1 Aisle.  Aisles shall comply with V403.

V904.3.2 Counter.  The counter surface height shall be 38 inches (965 mm) maximum above the finish deck surface.  The top of the counter edge protection shall be 2 inches (51 mm) maximum above the top of the counter surface on the aisle side of the check-out counter.

V904.3.3 Check Writing Surfaces.  Where provided, check writing surfaces shall comply with V902.3.

V904.4 Sales and Service Counters. Sales counters and service counters shall comply with V904.4.1 or V904.4.2.  The accessible portion of the counter top shall extend the same depth as the sales or service counter top.

EXCEPTION:  In alterations, when the provision of a counter complying with V904.4 would result in a reduction of the number of existing counters at work stations or a reduction of the number of existing mail boxes, the counter shall be permitted to have a portion which is 24 inches (610 mm) long minimum complying with V904.4.1 provided that the required clear deck space is centered on the accessible length of the counter.

V904.4.1 Parallel Approach.  A portion of the counter surface that is 36 inches (915 mm) long minimum and 36 inches (915 mm) high maximum above the finish deck surface shall be provided.  A clear deck space complying with V305 shall be positioned for a parallel approach adjacent to the 36 inch (915 mm) minimum length of counter.

EXCEPTION:  Where the provided counter surface is less than 36 inches (915 mm) long, the entire counter surface shall be 36 inches (915 mm) high maximum above the finish deck surface.

V904.4.2 Forward Approach.  A portion of the counter surface that is 30 inches (760 mm) long minimum by 36 inches (915 mm) high maximum shall be provided.  Knee and toe space complying with V306 shall be provided under the counter.  A clear deck space complying with V305 shall be positioned for a forward approach to the counter.

V904.5 Food Service Lines.  Counters in food service lines shall comply with V904.5.

V904.5.1 Self-Service Shelves and Dispensing Devices.  Self-service shelves and dispensing devices for tableware, dishware, condiments, food, and beverages shall comply with V308.

V904.5.2 Tray Slides.  The tops of tray slides shall be 28 inches (710 mm) minimum and 34 inches (865 mm) maximum above the finish deck surface.

V904.6 Security Glazing.  Where counters or teller windows have security glazing to separate personnel from the passengers, a method to facilitate voice communication shall be provided.  Telephone handset devices, if provided, shall comply with V704.3.