PVAG Chapter 3

CHAPTER 3: BUILDING BLOCKS

V301 General

V301.1 Scope.  The provisions of Chapter 3 shall apply where required by Chapter 2 or where referenced by a requirement in this document.

V302 Deck Surfaces

V302.1 General.  Deck surfaces shall be stable, firm, and slip resistant and shall comply with V302.

EXCEPTIONS:  Areas of sport activity shall not be required to comply with V302.

V302.2 Carpet.  Carpet or carpet tile shall be securely attached and shall have a firm cushion, pad, or backing or no cushion or pad.  Carpet or carpet tile shall have a level loop, textured loop, level cut pile, or level cut/uncut pile texture.  Pile height shall be ½ inch (13 mm) maximum.  Exposed edges of carpet shall be fastened to deck surfaces and shall have trim on the entire length of the exposed edge.  Carpet edge trim shall comply with V303.

V302.3 Openings.  Openings in deck surfaces shall not allow passage of a sphere more than ½ inch (13 mm) diameter except as allowed in V407.4.3 and V409.4.  Elongated openings shall be placed so that the long dimension is perpendicular to the dominant direction of travel.

EXCEPTION:  This requirement does not apply to vehicle tie-downs which are flush with the deck surface and are not located within an accessible route.

V303 Changes in Level

V303.1 General.  Where changes in level are permitted in deck surfaces, they shall comply with V303.

EXCEPTIONS:  1.  Areas of sport activity shall not be required to comply with V303.

2.  This requirement does not apply to vehicle tie-downs which are flush with the deck surface and are not located within an accessible route.

V303.2 Vertical.  Changes in level of ¼ inch (6.4 mm) high maximum shall be permitted to be vertical.

V303.3 Beveled.  Changes in level between ¼ inch (6.4 mm) high minimum and ½ inch (13 mm) high maximum shall be beveled with a slope not steeper than 1:2.

V303.4 Ramps.  Changes in level greater than ½ inch (13 mm) high shall be ramped, and shall comply with V405 or V406.

V304 Turning Space

V304.1 General.  Turning space shall comply with V304.

V304.2 Deck Surfaces.  Deck surfaces of a turning space shall comply with V302.  Changes in level are not permitted.

EXCEPTION:  Slopes not steeper than 1:48 shall be permitted.

V304.3 Size.  Turning space shall comply with V304.3.1 or V304.3.2.

V304.3.1 Circular Space.  The turning space shall be a space of 60 inches (1525 mm) diameter minimum.  The space shall be permitted to include knee and toe clearance complying with V306.

V304.3.2 T-Shaped Space.  The turning space shall be a T-shaped space within a 60 inch (1525 mm) square minimum with arms and base 36 inches (915 mm) wide minimum.  Each arm of the T shall be clear of obstructions 12 inches (305 mm) minimum in each direction and the base shall be clear of obstructions 24 inches (610 mm) minimum.  The space shall be permitted to include knee and toe clearance complying with V306 only at the end of either the base or one arm.

V304.4 Door Swing.  Doors shall be permitted to swing into turning spaces.

V305 Clear Deck Space

V305.1 General.  Clear deck space shall comply with V305.

V305.2 Deck Surfaces.  Deck surfaces of a clear deck space shall comply with V302.  Changes in level are not permitted.

EXCEPTION:  Slopes not steeper than 1:48 shall be permitted.

V305.3 Size.  The clear deck space shall be 30 inches (760 mm) minimum by 48 inches (1220 mm) minimum.

V305.4 Knee and Toe Clearance.  Unless otherwise specified, clear deck space shall be permitted to include knee and toe clearance complying with V306.

V305.5 Position.  Unless otherwise specified, clear deck space shall be positioned for either forward or parallel approach to an element.

V305.6 Approach.  One full unobstructed side of the clear deck space shall adjoin an accessible route or adjoin another clear deck space.

V305.7 Maneuvering Clearance.  Where a clear deck space is located in an alcove or otherwise confined on all or part of three sides, additional maneuvering clearance shall be provided in accordance with V305.7.1 and V305.7.2.

V305.7.1 Forward Approach.  Alcoves shall be 36 inches (915 mm) wide minimum where the depth exceeds 24 inches (610 mm).

V305.7.2 Parallel Approach.  Alcoves shall be 60 inches (1525 mm) wide minimum where the depth exceeds 15 inches (380 mm).

V306 Knee and Toe Clearance

V306.1 General.  Where space beneath an element is included as part of clear deck space or turning space, the space shall comply with V306.  Additional space shall not be prohibited beneath an element but shall not be considered as part of the clear deck space or turning space.

V306.2 Toe Clearance.

V306.2.1 General.  Space under an element between the finish deck surface and 9 inches (230 mm) above the finish deck surface shall be considered toe clearance and shall comply with V306.2.

V306.2.2 Maximum Depth.  Toe clearance shall extend 25 inches (635 mm) maximum under an element.

V306.2.3 Minimum Required Depth.  Where toe clearance is required at an element as part of a clear deck space, the toe clearance shall extend 17 inches (430 mm) minimum under the element.

V306.2.4 Additional Clearance.  Space extending greater than 6 inches (150 mm) beyond the available knee clearance at 9 inches (230 mm) above the finish deck surface shall not be considered toe clearance.

V306.2.5 Width.  Toe clearance shall be 30 inches (760 mm) wide minimum.

V306.3 Knee Clearance.

V306.3.1 General.  Space under an element between 9 inches (230 mm) and 27 inches (685 mm) above the finish deck surface shall be considered knee clearance and shall comply with V306.3.

V306.3.2 Maximum Depth.  Knee clearance shall extend 25 inches (635 mm) maximum under an element at 9 inches (230 mm) above the finish deck surface.

V306.3.3 Minimum Required Depth.  Where knee clearance is required under an element as part of a clear deck space, the knee clearance shall be 11 inches (280 mm) deep minimum at 9 inches (230 mm) above the finish deck surface, and 8 inches (205 mm) deep minimum at 27 inches (685 mm) above the finish deck surface.

V306.3.4 Clearance Reduction.  Between 9 inches (230 mm) and 27 inches (685 mm) above the finish deck surface, the knee clearance shall be permitted to reduce at a rate of 1 inch (25 mm) in depth for each 6 inches (150 mm) in height.

V306.3.5 Width.  Knee clearance shall be 30 inches (760 mm) wide minimum.

V307 Protruding Objects

V307.1 General.  Protruding objects shall comply with V307.

V307.2 Protrusion Limits.  Objects with leading edges more than 27 inches (685 mm) and not more than 80 inches (2030 mm) above the finish deck surface shall protrude 4 inches (100 mm) maximum horizontally into the circulation path.

EXCEPTION:  Handrails shall be permitted to protrude 4½ inches (115 mm) maximum.

V307.3 Required Clear Width.  Protruding objects shall not reduce the clear width required for accessible routes.

V307.4 Vertical Clearance.  Vertical clearance shall be 80 inches (2030 mm) high minimum.  Guardrails or other barriers shall be provided where the vertical clearance is less than 80 inches (2030 mm) high.  The leading edge of such guardrail or barrier shall be located 27 inches (685 mm) maximum above the finish deck surface.

EXCEPTIONS:  1.  Door closers and door stops shall be permitted to be 78 inches (1980 mm) minimum above the finish deck surface.

2.  Where doors are required by the administrative authority to have coamings, measurements are permitted to be taken from the finish deck surface adjacent to the coamings and not the top of the coamings.

V308 Reach Ranges

V308.1 General.  Reach ranges shall comply with V308.

V308.2 Forward Reach.

V308.2.1 Unobstructed.  Where a forward reach is unobstructed, the high forward reach shall be 48 inches (1220 mm) maximum and the low forward reach shall be 15 inches (380 mm) minimum above the finish deck surface.

V308.2.2 Obstructed High Reach.  Where a high forward reach is over an obstruction, the clear deck space shall extend beneath the element for a distance not less than the required reach depth over the obstruction.  The high forward reach shall be 48 inches (1220 mm) maximum where the reach depth is 20 inches (510 mm) maximum.  Where the reach depth exceeds 20 inches (510 mm), the high forward reach shall be 44 inches (1120 mm) maximum and the reach depth shall be 25 inches (635 mm) maximum.

V308.3 Side Reach.

V308.3.1 Unobstructed.  Where a clear deck space allows a parallel approach to an element and the side reach is unobstructed, the high side reach shall be 48 inches (1220 mm) maximum and the low side reach shall be 15 inches (380 mm) minimum above the finish deck surface.

EXCEPTION:  An obstruction shall be permitted between the clear deck space and the element where the depth of the obstruction is 10 inches (255 mm) maximum.

V308.3.2 Obstructed High Reach.  Where a clear deck space allows a parallel approach to an element and the high side reach is over an obstruction, the height of the obstruction shall be 34 inches (865 mm) maximum and the depth of the obstruction shall be 24 inches (610 mm) maximum.  The high side reach shall be 48 inches (1220 mm) maximum for a reach depth of 10 inches (255 mm) maximum.  Where the reach depth exceeds 10 inches (255 mm), the high side reach shall be 46 inches (1170 mm) maximum for a reach depth of 24 inches (610 mm) maximum.

EXCEPTION:  The top of washing machines and clothes dryers shall be permitted to be 36 inches (915 mm) maximum above the finish deck surface.

V309 Operable Parts

V309.1 General.  Operable parts shall comply with V309.

V309.2 Clear Deck Space.  A clear deck space complying with V305 shall be provided.

V309.3 Height.  Operable parts shall be placed within one or more of the reach ranges specified in V308.

V309.4 Operation.  Operable parts shall be operable with one hand and shall not require tight grasping, pinching, or twisting of the wrist.  The force required to activate operable parts shall be 5 pounds (22.2 N) maximum.